[ Air Filters ] [ Aluminum Heads ] [ Blowers ] [ Stud and Bolt ] [ Camshafts ] [ Competition Cams Brand Name Cams ] [ Cap and Wires ] [ Classified Ads Page ] [ Carburetors ] [ Cast Blocks ] [ Fuel Cells ] [ Cast Heads ] [ Clutches ] [ Computers ] [ Con Rods ] [ Consultation ] [ Torque Converters ] [ Forged Crankshafts ] [ Gears Axles Differentials ] [ Disclaimer ] [ Simulator ] [ Marine ] [ Street Car ] [ Home ] [ Customers ] [ Biography ] [ Engine Concepts Page ] [ Street ] [ News ] [ Links ] [ Sales Page ] [ Main Contents ] [ Support ] [ Class Specs ] [ Stockers ] [ Graphics ] [ Dragsters ] [ Pulling Tractors ] [ Projects ] [ Ignition Distrib ] [ Events Page ] [ Driveshafts ] [ Engine Assembly ] [ Fuel Injection ] [ Headers ] [ Engine kits ] [ Machine Shop ] [ Intakes ] [ Main Caps ] [ Nitrous ] [ Pistons ] [ Porting ] [ Pulleys ] [ Safety ] [ ComputerSim ] [ Starters ] [ Timing Sets ] [ Trans ] [ ValveTrain ] [ Merlin Crated Racing Engines & Parts/Supplies www.racingengines.com ] [ World Products Merlin Crate Engine Limited Warranty ]

LaPouttre Racing Heads \ Engines

Cylinder Head Porting

Stage 1: Hi performance valve job, pocket porting (bowls) and

general clean up   V-8 From $425  -   V-6 From $325  -  4 Cyl. From $215

Stage 2 : above stage 1 +  intake & exhaust port openings matched

to proprietary templates, guides smoothed,  ports polished

  V-8 From $750  -  V-6 From $550  -   4 Cyl. From $375

Stage 3 : above stage 1+2, Full porting and polishing, Flow tested

and Matched    V-8 From  $1250.00  - V-6 From $950.00 - 4 Cyl. From $625

Stage 4 : all of the above stages + Full race only modifications,

Quotes for special Nitrous,  Blown, turbocharged or large cubic

inch applications. Call for Quotes and specific applications.

Required  milling, casting repair, and special modifications / fabrications may be required and are additional

Click links to view pictures  

Dart 360 exhaust port (typical)     360 chamber(Nitrous)    

W-2 exhaust port (typical)  600 CFM Flow Bench 

Complete Cylinder Head Rebuilding

Unleaded / Hardened Valve Seat Installation

Seat Grinding and Installed Spring Heights Measured & Adjusted

Cylinder Heads Milled,  Flat or Custom Angle Milling

Carburetor / Injector Base Plate Fabrication / Modifications

Fuel / NOS. Plumbing and hardware layout

Cylinder Head Rebuilding Prices are as follows

• Comp 5 Angle Valve Job                            $150   (Titanium Valves $20 Extra)
• Head Milling/Resurfacing                            $30 Per Head ("V" engines require to be done in pairs)
• Angled Head Milling                                    $250
• Valve Guides/ Bronze                                  $110 for all 16 on V8's P&L
• Cylinder Head Hot Tank                            $25
• Magnaflux (Inspection  Only)                     $20 (Additional Head Disassembly & Hot Tank may be required)
• Port Matching Head or Manifold              $100
• Flow Time                                                     $35 Hour Typically 1.5 hours to Flow A Pair Of Heads
• Manifold Milling                                           $35 Per Side

Our standard pricing is based on a scheduled book rate of $35 U.S. an hour as determined by LaPouttre Racing, in addition to the standard pricing  for all of our required parts, supplies, and machine shop services.  Prices are determined upon the specific services rendered and their application requirements, in addition to any external services and supplies used. Racer Express Services are available, but at an additional cost to the rates as described above.

Sales@racingengines.com   Quotes

There have been Hits on this page